general
- g
gray-school-86965
02/27/2022, 1:41 PM! - g
gray-school-86965
02/27/2022, 1:41 PMcool project btw - b
bored-island-21407
02/27/2022, 1:42 PMwe think it has potential - g
gray-school-86965
02/27/2022, 1:43 PMinternet within the internet - g
gray-school-86965
02/27/2022, 1:43 PMi think so too - s
straight-lock-3524
02/27/2022, 4:29 PMas long as the internet works 😛 - i
important-photographer-59801
02/28/2022, 9:03 AMHi! - i
important-photographer-59801
02/28/2022, 9:04 AMYou guys have been busy! I've just upgraded my 0.8.5 netmaker to 0.11.0 - everything is different! - i
important-photographer-59801
02/28/2022, 9:05 AMI think I'm having a bit of trouble with the setup though. I've added all nodes to my network again,
and everything shows healthy in the dashboard. After about 5-10 mins, it goes to warning then errornetclient pull - i
important-photographer-59801
02/28/2022, 9:06 AMI suspect its related to the comms network and my router firewall. Is there a way I can control the UDP ports on the comms network? I suspect I need some portforwarding rules on my firewall, and dont particularly want to open up a whole range. - i
important-photographer-59801
02/28/2022, 9:10 AMwhenever I try to make any changes to the comms network via the dashboard, I get:{"Code":500,"Message":"cannot access comms network"} - i
important-photographer-59801
02/28/2022, 10:27 AMIn the netmaker backend container I also see the log
. I have setprocessed request error: cannot access comms network
to 3VERBOSITY - q
quiet-continent-24852
02/28/2022, 1:08 PMDid you upgrade your existing server in place or wipe it first? And are you running with CLIENT_MODE=on? - i
important-photographer-59801
02/28/2022, 1:41 PMi wiped it - i
important-photographer-59801
02/28/2022, 1:42 PMyes, client mode is on - q
quiet-continent-24852
02/28/2022, 1:57 PMOkay awesome, were you trying to edit something on it? - p
powerful-hydrogen-97244
02/28/2022, 2:00 PM - p
powerful-hydrogen-97244
02/28/2022, 2:00 PMmaybe this is related? - p
powerful-hydrogen-97244
02/28/2022, 2:00 PMfor me, it's a fresh install on a dedicated server - p
powerful-hydrogen-97244
02/28/2022, 2:00 PMthe clients run via docker on different nodes. After about 5-10 minutes I get errors - p
powerful-hydrogen-97244
02/28/2022, 2:01 PM[netmaker] 2022-02-28 14:00:03 error decrypting when updating node e7f66193-dbd8-44a9-aba8-9085d3dc0874 recieved invalid message from broker [] - i
important-photographer-59801
02/28/2022, 2:20 PMthanks @User - checking if this is my problem... - p
powerful-hydrogen-97244
02/28/2022, 2:40 PMthere is sadly no solution just yet - i
important-photographer-59801
02/28/2022, 2:41 PMi dont see those error messages anywhere though - i
important-photographer-59801
02/28/2022, 2:42 PMi have set VERBOSITY to 3, its not clear why things are connecting, but I strongly suspect its firewall ports for me - i
important-photographer-59801
02/28/2022, 2:44 PMI read the doc on the architecture channel, and it says its a hub/spoke type topology. Am I right in saying each node needs to open a wg udp listen port, and the netmaker server also needs an open wg udp listening port just for the comms network - q
quiet-continent-24852
02/28/2022, 2:45 PMwe will have to allow editing of the comms network I think to better suit cases like yours @User, so you can assign static ports for your comms. The docker netclient fix will be out later this week @User - i
important-photographer-59801
02/28/2022, 2:45 PMI cant see how to assign the static ports, since the UI doesnt let me update the config. It cant access the comms network ironically - q
quiet-continent-24852
02/28/2022, 2:46 PMright, we disallowed this to reduce user errors, but we will re-allow it in 0.11.1 - i
important-photographer-59801
02/28/2022, 2:46 PMah got it! thanks very much